Nordictrack Bike Resistance Not Working: [How To Fix] (2024)

Sometimes we may earn commission from qualifying purchases through links - at no extra cost to you.

Do you have a NordicTrack bike that’s not providing the resistance you need

If so, you’re not alone. This is a common problem that can be frustrating and inconvenient. But don’t worry, there’s a fix! In this guide, I’ll walk you through the steps to troubleshoot and repair a NordicTrack bike that’s not working properly. By the end of this guide, you’ll be able to get your bike back up and running in no time.

Why Nordictrack Bike Resistance Not Working

The resistance knob is not turned to the desired level.

:
Make sure the resistance knob is turned to the desired level.

The resistance cable is damaged or disconnected.

:
Inspect the resistance cable for damage or kinks. If the cable is damaged, it will need to be replaced. If the cable is disconnected, reconnect it.

The resistance unit is not working properly.

:
If the resistance unit is not working properly, it will need to be repaired or replaced.

The bike’s electronics are not working properly.

:
If the bike’s electronics are not working properly, they will need to be repaired or replaced.

How to Troubleshoot: nordictrack bike resistance not working

Symptoms

The resistance on your NordicTrack bike is not working properly.
The resistance level does not change when you adjust the knob.
The resistance is too high or too low, even when you adjust the knob.
The resistance is not consistent, and it changes without you adjusting the knob.

Causes

There are a few possible causes for a NordicTrack bike resistance not working properly.

The resistance knob is not properly adjusted:
Make sure that the knob is turned all the way to the right to increase resistance, and all the way to the left to decrease resistance.

The resistance cable is damaged or disconnected:
The resistance cable is a metal cable that connects the resistance knob to the resistance mechanism. If the cable is damaged or disconnected, it will not be able to transmit the signal from the knob to the mechanism.

The resistance mechanism is damaged:
The resistance mechanism is a set of gears and pulleys that create resistance when you pedal. If the mechanism is damaged, it will not be able to create the necessary resistance.

How to Fix It

To troubleshoot a NordicTrack bike resistance not working problem, you will need to inspect the resistance knob, resistance cable, resistance mechanism, and console.

Check the resistance knob:
Make sure that the knob is turned all the way to the right to increase resistance, and all the way to the left to decrease resistance. If the knob is not properly adjusted, you can try adjusting it and see if that fixes the problem.

Check the resistance cable:
Inspect the resistance cable for damage or kinks. If the cable is damaged, you will need to replace it. To check if the cable is disconnected, you can try wiggling it while you are pedaling. If the resistance changes when you wiggle the cable, the cable is disconnected and you will need to reconnect it.

Check the resistance mechanism:
Inspect the resistance mechanism for damage. If the mechanism is damaged, you will need to replace it.

Check the console:
Make sure that the console is properly calibrated. To calibrate the console, follow the instructions in the owner’s manual.

If you have checked all of the above and the problem persists, you may need to contact a qualified technician for help.

How to FIX: nordictrack bike resistance not working

Instructions

To fix a NordicTrack bike resistance not working problem, you will need to follow these steps:

1. Turn off the bike and unplug it from the power outlet:

2. Remove the seat and seat post.
3. Locate the resistance knob.
4. Inspect the resistance knob for damage or kinks.
5. If the resistance knob is damaged, replace it.
6. Reconnect the seat and seat post.
7. Turn on the bike and plug it back into the power outlet.
8. Test the resistance knob to make sure that it is working properly.

Troubleshooting

If the resistance knob is not working properly, you may need to troubleshoot the problem. Here are some things to check:

Make sure that the resistance knob is turned all the way to the right to increase resistance, and all the way to the left to decrease resistance.
Check the resistance cable for damage or kinks.
Inspect the resistance mechanism for damage.
Make sure that the console is properly calibrated.

If you have checked all of these things and the problem persists, you may need to contact a qualified technician for help.

Also Read: Nordictrack Bike Screen Not Working